Halftux at 11:09, 20 October 2023

2023-10-20T11:09:06Z

← Older revision		Revision as of 11:09, 20 October 2023
Line 5:		Line 5:
	\|dimensions=130x68.9x7.1mm		\|dimensions=130x68.9x7.1mm
	\|release_date=11-11-11		\|release_date=11-11-11
	\|soc=TI OMAP4430		\|soc=TI OMAP4430 <br>Cortex-A9 <br>Armv7‑A
	\|dram=1024MB DDR2		\|dram=1024MB DDR2
	\|power=		\|power=

Uvos at 20:18, 4 December 2022

2022-12-04T20:18:29Z

← Older revision		Revision as of 20:18, 4 December 2022
Line 17:		Line 17:
	\|sensors=		\|sensors=
	\|other=		\|other=
	\|category=~~Supported~~		\|category=unsupported
	\|sw_kernel=6.1		\|sw_kernel=6.1
	\|sw_serial=Yes, [[#Serial Cable\|special cable]]		\|sw_serial=Yes, [[#Serial Cable\|special cable]]

Uvos: Uvos moved page Razr to Motorola Razr (2011)

2022-12-04T20:11:57Z

Uvos moved page Razr to Motorola Razr (2011)

← Older revision	Revision as of 20:11, 4 December 2022
(No difference)

Uvos at 20:11, 4 December 2022

2022-12-04T20:11:12Z

← Older revision		Revision as of 20:11, 4 December 2022
Line 51:		Line 51:
	\|sw_frontcam=No		\|sw_frontcam=No
	\|sw_backcam=No		\|sw_backcam=No
	\|sw_idlepower=~~120mW~~		\|sw_idlepower=Unkown
	\|sw_standbytime=		\|sw_standbytime=
	}}		}}

Uvos: Created page with "{{Infobox Device |image=250px |manufacturer=Motorola |codename=Spyder XT910, XT912 |dimensions=130x68.9x7.1mm |release_date=11-11-11 |soc=TI OMAP4..."

2022-12-04T20:10:24Z

Created page with "{{Infobox Device |image=250px |manufacturer=Motorola |codename=Spyder XT910, XT912 |dimensions=130x68.9x7.1mm |release_date=11-11-11 |soc=TI OMAP4..."

New page

{{Infobox Device
|image=[[File:XT910Lockscreen.jpg|250px]]
|manufacturer=Motorola
|codename=Spyder XT910, XT912
|dimensions=130x68.9x7.1mm
|release_date=11-11-11
|soc=TI OMAP4430
|dram=1024MB DDR2
|power=
|lcd=960x540 4.3"
|video=PowerVR SGX540
|audio=
|network=
|storage=16GB flash
|usb=
|camera=
|sensors=
|other=
|category=Supported
|sw_kernel=6.1
|sw_serial=Yes, [[#Serial Cable|special cable]]
|sw_charging=Yes
|sw_usb_slave=Yes
|sw_usb_host=Yes
|sw_touchscreen=Yes
|sw_keyboard=Yes
|sw_screen=Yes
|sw_hdmi=Yes
|sw_tv=
|sw_3daccel=Yes [https://github.com/maemo-leste/pvr-omap4] (closed)
|sw_vibration=Unkown
|sw_audio=Unkown
|sw_calls=Unkown
|sw_sms=Unkown
|sw_wifi=Yes
|sw_ethernet=
|sw_irda=
|sw_2g3gdata=Unkown
|sw_4g=No
|sw_bluetooth=Yes, [[#Bluetooth|see notes]]
|sw_fmtx=No
|sw_fmrx=
|sw_nfc=
|sw_accelerometer=No
|sw_compass=No
|sw_gyro= No
|sw_proximity=Yes
|sw_als=No
|sw_gps=Unkown
|sw_agps=No
|sw_frontcam=No
|sw_backcam=No
|sw_idlepower=120mW
|sw_standbytime=
}}

== Installation ==

Hardware requirements:

* A Razr or Droid Razr or Droid Razr MAXX with fully charged battery
* MicroUSB cable
* MicroSD card

Software requirements:
* Host Linux or Windows system
* Android Tools: fastboot
* get allow-mbmloader-flashing-mbm.bin for your device (xt910 or xt912) from an android update zip
* Flashing tools:
** XZ Utils and coreutils for Linux
** Etcher[https://github.com/balena-io/etcher] for Windows

Download from https://github.com/tmlind/droid4-kexecboot.git

# utags-xt910-16-mmcblk1p8-boots-mmcblk1p13-kexecboot.bin
# droid4-kexecboot.img

Installation:

# Create a working directory with above mentioned files in it
# Power off the Razr and connect it to the host machine with MicroUSB cable
# Start the device in fastboot mode. For this press power button and bottom volume key simultaneously and release them after a second.

=== Setting up kexecboot ===

Now, assuming you are in the working directory, install kexecboot:

<pre>
sudo fastboot flash mbm allow-mbmloader-flashing-mbm.bin
sudo fastboot reboot-bootloader
sudo fastboot flash bpsw droid4-kexecboot.img
sudo fastboot flash utags utags-xt910-16-mmcblk1p8-boots-mmcblk1p13-kexecboot.bin
sudo fastboot reboot
</pre>

The device should reboot and show kexecboot menu for a few seconds before it boots to Android.

=== Install Maemo Leste to the sdcard ===

Now, flash the Maemo Leste image to your sdcard:

On Linux:
<pre>
xzcat maemo-leste-1.0-armhf-razr-$DATE.img.xz | sudo dd status=progress bs=1M of=/dev/MICROSDCARD-DEVICE
sync
</pre>

On Windows: Use Etcher

Wait for sync to complete and insert MicroSD card into the Razr. Reboot the device and select Maemo Leste from the kexecboot menu.

You should now see Maemo Leste booting up, and it will show you hildon-desktop after a minute.

== Updating ==

Normally you can just apt update && apt dist-upgrade to update to the latest version. If for some reason this fails:

* Poweroff device, grab the SD card
* Backup any important files
* Grab the latest image from https://phoenix.maemo.org/view/Images/
* Write it as before : xzcat maemo-leste-1.0-armhf-droid4-20190227.img.xz | sudo dd status=progress bs=1M of=/dev/MICROSDCARD-DEVICE

== Notes ==

The battery in Razr is not easily removable. If you got the device stuck, use this combo: power button + bottom volume key. You should hold them for about 7 seconds. Razr will then reboot.

== Serial Cable ==

As explained at http://muru.com/linux/d4 , the Droid 4 exposes a serial console on the USB port. You can construct the required cable easily by following the instructions there. If you have old Nokia CA-42 or DKU-5 cables, then you can use them with the Razr, using instructions at https://jethomson.wordpress.com/2010/02/21/diy-usb-to-serial-cable-for-3usd/

== Bluetooth ==

Needs firmware - install latest firmware-ti-connectivity - See also https://github.com/maemo-leste/bugtracker/issues/290. Due to interference with WiFi, load driver (hci_uart) manually, AFTER wifi module loaded

Using a bluetooth headset:
sudo apt install pulseaudio-module-bluetooth blueman bluez
sudo modprobe hci_uart
pactl load-module module-bluetooth-discover
blueman-manager

Pair & trust your device in blueman, connect audiosink. You can close blueman now.

== Additional Tips ==

==== Using a battery without temperature sensor ====

Modprobe the pmic driver as follows:
<pre>
cpcap-battery ignore_temperature_probe=1
</pre>

==== Flashing the boot logo ====

More info: https://github.com/xsetiadi/droid4-kexecboot/blob/master/LOGO

logos can be flashed via fastboot flash logo.bin logo.bin

==== HDMI ====
Move output to external 1080p monitor. Disabling DSI-1 output gets xorg pointer displayed on HDMI, for use with a mouse or barrier.
<pre>
xrandr --output HDMI-1 --mode 1920x1080 --output DSI-1 --off
</pre>
Return to internal touchscreen display.
<pre>
xrandr --output DSI-1 --auto --rotate right --output HDMI-1 --off
</pre>

== Using a configured Leste sdcard in a different Razr ==

A configured Razr Leste installation will have a unique wlan firmware calibration. The wifi calibration script requires a system set to stock settings to calibrate-from. It cannot just be re-run on an already calibrated system.

To recalibrate the wifi firmware on a different Razr, you must reset the FEM parameters to stock settings on the new device, then recalibrate.
If you can get the device online (usb networking or moving close to the WLAN AP) this can be done with.
apt reinstall firmware-ti-connectivity
If not, you can download the firmware-ti-connectivity_[version]_all.deb on another Leste device
apt download firmware-ti-connectivity
Then copy the .deb to your new device and install that (as root) with
dpkg -i firmware-ti-connectivity_[version]_all.deb
Then (as root) re-calibrate the wifi chip by running
/usr/bin/maserati-calibrate
Then reboot.
[[Category:Device]]

Motorola Razr (2011) - Revision history

Halftux at 11:09, 20 October 2023

Uvos at 20:18, 4 December 2022

Uvos: Uvos moved page Razr to Motorola Razr (2011)

Uvos at 20:11, 4 December 2022

Uvos: Created page with "{{Infobox Device |image=250px |manufacturer=Motorola |codename=Spyder XT910, XT912 |dimensions=130x68.9x7.1mm |release_date=11-11-11 |soc=TI OMAP4..."