View source for A23-Q8H-v1.5

{{Infobox Device
|image=[[File:A23-q8h-v1.5-ccit.jpg|250px|alt=image of Q8H tablet, running leste]]
|manufacturer=CCIT? (Ippo?)
|codename=Q8H v1.5
|dimensions=181mm x 121mm x 10.5mm
|release_date=2015-01-29
|category=Supported
|soc=Allwinner A23 @1.5Ghz <br>underclocked @1.2Ghz<br>Cortex-A7<br>Armv7-A
|dram=512MiB DDR3 @ 480MHz 
|power=DC 5V @ 2A
|lcd=800x480 7" capacitive touch
|video=Mali 400
|audio=3.5mm headphone plug, internal speaker, internal microphone 
|network=RTL8703AS
|storage=4GB?
|usb=Micro USB 2.0 Host
|camera=0.3MP (640x480)
|sensors=
|other=
|headers=UART?
|battery=?mAh 3.7V Li-Ion battery 
|sw_kernel=6.12
|sw_serial=N/A
|sw_charging=Yes
|sw_usb_slave=Gadgets only
|sw_usb_host=With hacks
|sw_touchscreen=Yes, single-touch
|sw_keyboard=N/A
|sw_screen=Yes
|sw_hdmi=N/A
|sw_tv=No
|sw_3daccel=Yes
|sw_vibration=Yes
|sw_audio=Yes
|sw_calls=N/A
|sw_sms=N/A
|sw_wifi=Yes, firmware required
|sw_ethernet=N/A
|sw_irda=N/A
|sw_2g3gdata=N/A
|sw_4gdata=N/A
|sw_bluetooth=Yes, firmware required
|sw_fmtx=N/A
|sw_fmrx=N/A
|sw_nfc=N/A
|sw_accelerometer=Yes
|sw_compass=N/A
|sw_gyro=N/A
|sw_proximity=N/A
|sw_als=N/A
|sw_gps=N/A
|sw_agps=N/A
|sw_frontcam=N/A
|sw_backcam=N/A
|sw_idlepower=1.4W-3.7W (WIP)
|sw_standbytime=N/A
}}

== Installation ==
Simply write the image to a sdcard and put it on the device, it should load u-boot and kernel automatically.

== Notes ==
Like most devices with silead touch screen you may need to extract touch screen driver from android firmware. firmware for this tablet was <code>gsl1680-b482-q8-a70.fw</code>, which could be either taken from [https://github.com/onitake/gsl-firmware here] or from android directly.
while the screen resolution was 800 x 480, touch panel had 900 x 600.

=== Wireless and Bluetooth ===
On devices that ship with realtek 8702as (or 8723bs), a firmware and a binary config file are required for wifi/bluetooth driver to work properly.
these are available under package <code>firmware-realtek</code>.
a patch is needed for bluetooth driver to work properly, which is just for correct probing of the card.

note that sdio currently doesn't function if device is rebooted, powering it off and turning it on again works.

=== Power usage ===
Hungry beast, sips 1A with everything on and max and sips 300mA with everything (but wifi) off and cpu mostly idle.
this results in very poor temps and runtime, some of which can be improved thru [https://github.com/crust-firmware/crust crust] (since appearently deep sleep support in mainline for allwinner kernels is very poor, if non existant?) or better dt/kernel setups.

== Status ==
{| class="wikitable"
! Feature
! Leste supported
! Notes
|-
| Kernel version || 6.12 || Mainline + patches (for bluetooth, wireless and screen rotation)
|-
| Serial || Probably || Need to locate it on the board
|-
| Charging || Yes || charging via AC in works
|-
| Wireless || Yes || Realtek 8703as, Driver is still in staging (rt8723bs)
|-
| Bluetooth || Yes? || Realtek 8703as, Uses rt8723bs driver, seems to work, but not tested much
|-
| Micro USB || WIP || Only works in otg (with dr_mode = "host" in dts), might need further device tree improvments
|-
| Keyboard || N/A || Device has no keyboard
|-
| Screen || Yes || sunxi drm (with simplefb)
|-
| 3D Acceleration || Yes || Mali 400, Lima
|-
| Touchscreen || Yes || Silead gsl1688?, Capacitive
|-
| Speaker || WIP || works, but a bit underwhelming, might be amplifiers
|-
| Headphone || WIP || works, but does not mute speakers when plugged in
|-
| Accelerometer || Yes? || Memsic 6255, There is a screen rotation sensor, mxc6255 driver can be used for it, but doesn't seem to work very well
|-
| Proximity sensor || N/A || Not sure if available
|-
| eMMC || No || Likely dts issues
|-
| HW accelerated video encode/decode || ? || Should work with Cedrus driver, but not tested
|-
| Camera || ? || Not tested
|}

[[Category:Device]]