Difference between revisions of "Motorola Droid Bionic"
| (6 intermediate revisions by 3 users not shown) | |||
| Line 2: | Line 2: | ||
|image=[[File:Bionic.jpg|250px]] | |image=[[File:Bionic.jpg|250px]] | ||
|manufacturer=Motorola | |manufacturer=Motorola | ||
|codename=Targa | |codename=Targa XT875 | ||
|dimensions=127x67.3x12.7mm | |dimensions=127x67.3x12.7mm | ||
|release_date= | |release_date=2011-09-8 | ||
|soc=TI OMAP4430 | |soc=TI OMAP4430 | ||
|dram=1024MB DDR2 | |dram=1024MB DDR2 | ||
| Line 18: | Line 18: | ||
|other= | |other= | ||
|category=Supported | |category=Supported | ||
|sw_kernel=5. | |sw_kernel=5.18.x | ||
|sw_serial=Yes, [[#Serial Cable|special cable]] | |sw_serial=Yes, [[#Serial Cable|special cable]] | ||
|sw_charging=Yes | |sw_charging=Yes | ||
| Line 31: | Line 31: | ||
|sw_vibration=Yes | |sw_vibration=Yes | ||
|sw_audio=Yes | |sw_audio=Yes | ||
|sw_calls= | |sw_calls=Yes | ||
|sw_sms=Yes | |sw_sms=Yes | ||
|sw_wifi=Yes | |sw_wifi=Yes | ||
|sw_ethernet= | |sw_ethernet= | ||
| Line 93: | Line 93: | ||
You should now see Maemo Leste booting up, and it will show you hildon-desktop after a minute. | You should now see Maemo Leste booting up, and it will show you hildon-desktop after a minute. | ||
== Notes == | == Notes == | ||
| Line 141: | Line 132: | ||
</pre> | </pre> | ||
<pre> | <pre> | ||
22:37 < tmlind> i also had to do tcmdrw 6850=05 for 3g voice to work properly | |||
< | |||
</pre> | </pre> | ||
== Stuff to try == | |||
==== 3G Internet ==== | ==== 3G Internet ==== | ||
Latest revision as of 12:52, 16 August 2022
| Motorola Droid Bionic | |
|---|---|
 | |
| Manufacturer | Motorola |
| Codename | Targa XT875 |
| Dimensions | 127x67.3x12.7mm |
| Release Date | 2011-09-8 |
| Category | Supported |
| Specifications | |
| SoC | TI OMAP4430 |
| DRAM | 1024MB DDR2 |
| Hardware Features | |
| LCD | 960x540 4.3" |
| Video | PowerVR SGX540 |
| Storage | 16GB flash |
| Sensors | AK8975 compass, Kionix KXTf9 accelerometer, St L3GD20H Gyro, ISL29030 proximity and illuminance, TMP105 temperature sensor |
| Software Features | |
| Kernel | 5.18.x |
| Serial | Yes, special cable |
| Charging | Yes |
| USB Slave | Gadgets only |
| USB Host | No |
| Touchscreen | Yes |
| Screen | Yes |
| HDMI-out | Yes |
| 3D acceleration | Yes, [closed driver|] |
| Vibration motor | Yes |
| Audio | Yes |
| Phone calls | Yes |
| SMS | Yes |
| Wifi | Yes |
| 2G/3G data | Yes |
| Bluetooth | Yes, see notes |
| FM transmitter | No, but apparently exists, needs serdev kernel modules/drivers |
| Accelerometer | Yes |
| Compass | Yes, no integration |
| Gryo | No, needs kernel work |
| Proximity Sensor | Yes |
| Ambient Light Sensor | Yes |
| GPS | Yes |
| A-GPS | No, needs kernel/userspace work |
| Front Camera | No |
| Back Camera(s) | No |
| Idle Power Consumption | 70mW, needs sim inserted |
| Stand by time | 91.8h (with HW4X) |
Installation
Hardware requirements:
- Droid Bionic with fully charged battery
- MicroUSB cable
- MicroSD card
Software requirements:
- Host Linux system
- Android Tools: fastboot adb
- Flashing tools:
- XZ Utils and coreutils for Linux
- Etcher[1] for Windows
Download from https://phoenix.maemo.org/view/Images/job/leste-image-bionic/
- Latest maemo-leste-1.0-armhf-bionic-*.img.xz
Download from https://github.com/tmlind/droid4-kexecboot.git
- droid4-kexecboot.img
Download or clone https://github.com/IMbackK/bionic-clown-boot
Follow the instructions in bionic-clown-boot's readme to install kexecboot on your device.
Now, flash the Maemo Leste image to your sdcard:
On Linux:
xzcat maemo-leste-1.0-armhf-droid4-20190227.img.xz | sudo dd status=progress bs=1M of=/dev/MICROSDCARD-DEVICE sync
Wait for sync to complete and insert MicroSD card into The Bionic. Reboot the device and select Maemo Leste from the kexecboot menu.
You should now see Maemo Leste booting up, and it will show you hildon-desktop after a minute.
Notes
Some users reported that Bluetooth kernel module interfere badly with the WiFi driver on their devices. Blacklisting the module may help if you have such problems:
echo "blacklist hci_uart" >> /etc/modprobe.d/blacklist.conf
Also see Motorola_Droid_4/Modem Motorola_Droid_4/PowerVR
Also see: http://elektranox.org/droid4/ and http://muru.com/linux/d4/
Serial Cable
As explained at http://muru.com/linux/d4 , the Droid 4 and Bionic both expose a serial console on the USB port. You can construct the required cable easily by following the instructions there. If you have old Nokia CA-42 or DKU-5 cables, then you can use them with the Bionic, using instructions at https://jethomson.wordpress.com/2010/02/21/diy-usb-to-serial-cable-for-3usd/
Bluetooth
Needs firmware - install latest firmware-ti-connectivity - See also https://github.com/maemo-leste/bugtracker/issues/290. Due to interference with WiFi, load driver manually, AFTER wifi module loaded
Unlocking the modem for usage in Europe
Tony suggested these values, Wizzup confirmed it to work on his Bionic in Europe/Amsterdam.
apt install build-essential git clone https://github.com/tmlind/tcmdrw cd tcmdrw make ./tcmdrw 1877=8703E80400000200 ./tcmdrw 6850=05
Tony also writes:
22:34 < tmlind> hmm so i had to do this for 3g gain: tcmdrw 1143=aaff0000, got that value from xt910 firmware i think, otherwise 3g signal was weak 22:43 < tmlind> Wizzup: great, the 1143 setting is for 1900 frequency only to get decent signal on t-mo in the us
22:37 < tmlind> i also had to do tcmdrw 6850=05 for 3g voice to work properly
Stuff to try
3G Internet
22:12 < pave1> qmicli -d /dev/cdc-wdm0 --wds-follow-network --wds-start-network=apn=internet.t-mobile.cz 22:12 < pave1> route del default 22:12 < pave1> sudo ifconfig wwan0 up 22:12 < pave1> dhclient wwan0
GPS
modprobe gnss-motmdm and point gpsd to use /dev/gnss0
22:30 < tmlind> hmm there's a probably kernel gnss bug for gsp access fyi, you can currently only open one connection before you have to restart gpsd :)
Can try to
mkfifo /tmp/gps cat /dev/gnss0 > /tmp/gps Then point gpsd to use /tmp/gps
USSD
22:45 < tmlind> fyi, here's how to send USSD to query balance for example: printf "AT+CUSD=1,#999#,0\r" > /dev/motmdm1
22:47 < tmlind> fyi, for parsing incoming USSD, this web interface works if set to utf-8:
https://www.mobilefish.com/services/latin_utf_base64_to_hex/latin_utf_base64_to_hex.php#text_hex_output
Old status table
| Feature | Leste supported | Notes |
|---|---|---|
| Kernel version | 5.10.4 | Mainline + some patches not yet in mainline - see https://github.com/maemo-leste/droid4-linux |
| Serial | Yes | On MicroUSB port, requires special cable |
| Charging | Yes | |
| USB slave | Yes | |
| USB host (OTG) | No | |
| Touchscreen | Yes | Capacitive |
| Keyboard | N/A | |
| Screen | Yes | |
| HDMI-out | Yes | No UI integration |
| TV-out | N/A | |
| 3D Acceleration | Yes | PowerVR SGX540 (closed driver) - https://github.com/maemo-leste/pvr-omap4/ |
| Vibration Motor | Yes | |
| Audio | Yes | Switch around in alsamixer to get the right outputs working ('Speaker Right' set to 'HiFi' and 'HiFi' set to above 0 gets you output) |
| Phone calls | WIP | Untested |
| SMS | Yes | Works with ofono. Needs Leste UI |
| Wifi | Yes | |
| Ethernet | N/A | |
| IrDA | N/A | Missing in hardware |
| 2G/3G data | Yes | Works with ofono, no UI yet - see https://github.com/maemo-leste/connui-cellular/ |
| 4G data | No | Needs kernel work |
| Bluetooth | Yes | Needs firmware - install latest firmware-ti-connectivity - See also https://github.com/maemo-leste/bugtracker/issues/290. Due to interference with WiFi, load driver manually, AFTER wifi module loaded |
| FM Transmitter | No | Apparently exists, and will need serdev kernel modules/drivers |
| FM Receiver | No | |
| Nfc | No | no hardware |
| Accelerometer | Yes | |
| Compass | Yes | Available in /sys (after loading ak8975 module. No Leste integration) |
| Gyro | No | needs kernel work |
| Proximity sensor | Yes | |
| Ambient Light Sensor | Yes | |
| GPS | Yes | Works with gpsd but is not integrated yet, see GPS |
| AGPS | No | |
| Front Camera | No | |
| Back Camera(s) | No | |
| Idle power consumption | ~70 mW | Needs sim inserted |
| Idle Battery life on new battery | 91.8 h | With HW4X |
